Do shaftless lifts require a traditional vertical shaft or head clearance?
Adding a lift to an existing home sounds simple until the building work comes up. A conventional elevator usually needs a constructed vertical shaft, a pit dug below the ground floor and a separate room for the motor. Each of these takes floor space, structural changes and weeks of on-site work. For many homeowners, the question is whether a home lift is suitable.
Hacking through walls and slabs creates dust, noise and disruption to daily life. Approvals, contractors and finishing work add cost and delay. Older homes may not have a suitable corner for a full shaft, and the space a shaft takes on every floor is space lost for good. Meanwhile, family members who struggle with stairs continue to do so.
Self-supporting lifts remove most of that burden. A shaftless design brings its enclosure, so there is no shaft to build, no pit to dig and no machine room to find space for. In this guide, we explain what a shaftless lift actually needs, what it does not, and how NIBAV Home Lifts approaches head clearance in a typical home.
Table of Contents
- What Does a Shaftless Home Lift Really Mean?
- What you still need to plan for
- How Much Room Do Nibav Home Lifts Need Above the Top Floor?
- What are Pitless Home Lift and Machine Room Less Home Lift?
- No pit at the ground floor
- No machine room above
- What difference does this mean on site
- How to Plan a Panoramic Home Lift with Nibav Home Lifts?
- Frequently Asked Questions
- 1. Does a shaftless home lift need a pit?
- 2. How much headroom does a shaftless lift need?
- 3. How much space is needed to install a home lift?
- 4. Can a shaftless lift be installed in an existing house?
- 5. How many floors can a shaftless home lift serve?
What Does a Shaftless Home Lift Really Mean?
The word “shaftless” causes some confusion. It means you do not have to build a hoistway out of the home’s own structure.
A conventional lift runs inside a reinforced shaft that the builder constructs, usually from concrete or masonry. That shaft holds the guide rails, takes the load and keeps people away from moving parts. It eats floor space on every level, and it has to be planned before the walls go up or cut in afterwards at real cost.
A shaftless home lift brings its enclosure with it. In the case of NIBAV Home Lifts, the lift sits inside a self-supported cylinder made of aluminium, galvanised steel and polycarbonate panels.
The brand states that this polycarbonate is 250 times stronger than ordinary glass. The cylinder stands on the finished floor and rises through openings in each slab. It does not lean on a beam, column or wall for support. That difference is what makes retrofitting a lift into an existing home realistic.
What you still need to plan for
- A slab opening on each upper floor. The cylinder passes through a round cut-out sized to its outer diameter. A structural engineer should confirm that the cut does not hit a beam.
- Floor space at every landing. This is the cylinder footprint plus a little working room, listed by Nibav Home Lifts as the clear space required.
- A single-phase power supply is needed.
How Much Room Do Nibav Home Lifts Need Above the Top Floor?
Yes, a shaftless lift still needs head clearance, but far less fuss than a traditional overrun. Head clearance (or headroom) is the vertical space between the top landing’s floor and the ceiling above it. The cabin needs this room to park at the highest stop, and the drive unit sits in the head of the cylinder.
For its Series III range, NIBAV Home Lifts lists a minimum headroom of 2,436 to 2,800 mm. Many Malaysian homes already have ceilings in that band, so the lift often fits under the existing roof slab without raising it. The exact figure for your home depends on the model and configuration and is confirmed during the site survey.
There is one more vertical limit worth knowing. Nibav Home lifts a maximum travel height of 13,500 mm, including the overhead portion, so the full run from the ground floor to the top of the unit cannot exceed that figure. In practice, that covers up to four stops (G+3) in most homes.
The table below brings together the published specifications for each current model.
| Vertical requirement | Conventional home lift | NIBAV Home Lifts |
| Headroom above top landing | Overrun space set by the lift type, often needing a raised roof slab | 2,436 to 2,800 mm (Series III range), usually within a normal ceiling |
| Pit below ground floor | Required: dug into the ground slab | Not required; rests on the finished floor |
| Machine room | Often needed, on the roof or in the shaft head | Not required; the drive sits in the head of the cylinder. |
| Vertical enclosure | Constructed concrete or masonry shaft | Self-supported polycarbonate cylinder |
| Opening through each floor | Full shaft-sized void | Round slab opening sized to the cylinder (933 mm standard, 1,363 mm max) |
| Cabin height | Varies by model | 1,950 mm (Series III range) |
All models share a maximum travel height of 13,500 mm, including overhead. The cabin height on the Series III range is 1,950 mm, with a clear door opening of 508 mm.
What are Pitless Home Lift and Machine Room Less Home Lift?
The shaft is only one of three big construction jobs in a conventional lift. The other two are the pit and the machine room, and removing them saves as much disruption as removing the shaft.
No pit at the ground floor
Traditional lifts need a recess below the lowest landing for buffers and the bottom of the car. On a ground-floor slab, that means breaking concrete, waterproofing the hole and sometimes dealing with groundwater. A pitless home lift skips all of it. Nibav Home Lifts cylinder rests directly on the finished floor, with no pit and no floor reinforcement required.
No machine room above
A traction lift usually needs space for its motor and controller, either in a room on the roof or squeezed into the shaft head. A machine room less home lift keeps its drive inside the unit. In Nibav home lifts air-driven design, the cabin rises as the system lowers the air pressure above it, so it needs no ropes, counterweights or hydraulic tank. The lift runs on single-phase power and, according to the brand, uses no electricity on the way down.
What difference does this mean on site
Without a shaft, pit or motor room to build, installation becomes an assembly job rather than a construction project. Nibav Home Lifts units arrive as a completely knocked down (CKD) kit and are typically installed in 4-5 working days. Because nothing is cast into the building, the lift can also be dismantled and moved if you relocate.
How to Plan a Panoramic Home Lift with Nibav Home Lifts?
Since the cylinder is see-through, a panoramic home lift is part of the room it stands in. That changes where you might put it. A conventional shaft gets hidden in a corner; a transparent unit can sit beside the staircase, in a double-height living area or near a window without blocking light. Families with a claustrophobic member often find the open view makes the ride far more comfortable.
Before a site visit, run through these checks yourself:
- Floor space measurement: Standard models need about 1,010 mm of clear space; max models need about 1,430 mm. Leave room in front of the door to step in and out comfortably.
- Ceiling height: Compare it with the 2,436 to 2,800 mm headroom range. Note any downlights, fans or false ceilings in that spot.
- Beams overhead: The slab opening must avoid structural beams on every floor the lift passes through.
- Count your stops: Up to four (G+3) are supported, and extra stops can be added later.
- Cabin size: Choose a Max model if a wheelchair user, an attendant, or three passengers will be riding together.
- Find a PowerPoint: A standard single-phase socket nearby keeps the wiring simple.
On safety, Nibav Home Lifts builds in several layers. If power fails, the car descends automatically to the ground floor, and the door can be opened by hand. An emergency landing switch inside and outside the cabin brings it down if it stops between floors.
The patented Sure Stop system locks the car within about 2 inches if pressure drops or speed rises abnormally. A rapid rescue latch and a manual door unlock round out the set. The products are TÜV NORD certified to European standards, and the company holds ISO 14001 and ISO 45001 certifications.
Frequently Asked Questions
1. Does a shaftless home lift need a pit?
No. A shaftless home lift from Nibav Home Lifts stands directly on the finished ground floor. It needs no pit, no floor reinforcement and no excavation, which makes it well suited to existing homes.
2. How much headroom does a shaftless lift need?
NIBAV Home Lifts lists a minimum headroom of 2,436 to 2,800 mm above the top landing for its Series III range. The exact figure for your home is confirmed during the site survey, based on model and layout.
3. How much space is needed to install a home lift?
Standard NIBAV Home Lifts models (Series III, IV and V) need about 1,010 mm of clear floor space, with an external cylinder diameter of 933 mm. Max models need about 1,430 mm, with a 1,363 mm cylinder.
4. Can a shaftless lift be installed in an existing house?
Yes. Because NIBAV Home Lifts units are self-supported and need no shaft, pit or machine room, they suit retrofits. The main civil work is a round opening in each upper floor slab, and installation usually takes 4-5 working days.
5. How many floors can a shaftless home lift serve?
NIBAV Home Lifts models serve up to four stops (G+3), with a maximum travel height of 13,500 mm including overhead. Stops can be added later if your needs change.